Dimming Technologies Choosing The Right Dimmer For Your

Browse technical resources about optical modules, laser chips, photonic ICs, and 5G/data center interconnect.

  • How to troubleshoot a dimming module malfunction

    How to troubleshoot a dimming module malfunction

    Follow these easy steps to narrow down the issue and determine whether you need professional support: Turn off the power at the breaker panel for safety. Remove the dimmer switch faceplate and inspect for loose wiring or damage. Check if your light bulbs are marked as “dimmable. Understanding the difference between a simple bulb. This guide will walk you through common problems and provide step-by-step solutions to get your dimmers working correctly. Master electrician Heath Eastman takes us on a road trip to solve a homeowner's dimmer problem. Dimming LEDs should be simple, but often isn't. Or you may have “dead areas” as you slide your dimmer switch.


  • Function of the switch-mode dimming module

    Function of the switch-mode dimming module

    Switch-mode dimmable LED drivers are known for their high efficiency and control over LED current. Most designers use one of two methods: analog dimming or digital pulse-width modulation (PWM) dimming. In both implementations, the LEDs will turn on or off according. To provide stable color control, the LED string must be driven with Pulse-Width Modulated (PWM) constant current pulses, often incorporating a load switch to disconnect the LED string from the output of the driver during the off-time. Both methods control the time-averaged current through an LED or LED string, but the differences between the two are also obvious when weighing the advantages and. As there are several ways to achieve dimming of an LED, we describe here the main methods that are used to provide dimming for LED's from a switch mode LED driver.


  • What are some fiber optic high-temperature sensing technologies

    What are some fiber optic high-temperature sensing technologies

    According to the temperature measurement principle, fiber-optic sensors can be divided into blackbody radiation sensors, fluorescence-based sensors, interferometric sensors, fiber Bragg grating (FBG) sensors, and distributed temperature sensors (DTS). In fiber-optic high-temperature sensing systems, various optical fibers are used as the sensor transducer, as the medium for data transmission, or both [27, 28]. These sensors utilize light transmission properties through optical fibers to detect temperature. Fiber optic temperature sensors are immune to the many environmental effects that compromise other measurement technologies, can be embedded and installed in locations traditional temperature sensors cannot and deliver an unprecedented level of spatial detail and data without sacrificing precision. A fiber optic temperature sensor is a temperature measurement device that uses optical fibers as the sensing medium. Unlike traditional electrical temperature sensors (e.

    [PDF Version]
  • Current Status of Key Technologies for Energy Internet

    Current Status of Key Technologies for Energy Internet

    This article deals with a thorough investigation of the energy internet towards future emerging technologies for energy distribution and management to solve existing limitations and enhance the performanc.


  • A small opening is made on the side of the cable tray to run the cable

    A small opening is made on the side of the cable tray to run the cable

    In a perforated cable tray configuration, the side and rails of the cable tray are perforated with a series of small holes. While this design is not necessarily as well-ventilated as a ladder tray, it also prevents moisture accumulation and allows for excellent heat dissipation. The B-Line series Cable Tray Manual was produced by our technical staff. The following pages address the 2014 National Electrical Code® requirements for cable tray systems as well as design. The exception is that 9 inches is the maximum allowable rung spacing for a ladder cable tray supporting any 1/0 through 4/0 single conductor cables [See Section 392. Standard Aluminum Ladder • The rungs provide a convenient anchor for tying down cables in vertical runs or where the. The primary rulebook of cable tray systems is called NEC Article 392. These regulations ensure that the metal or plastic frames that contain the wires are robust enough to ensure. A section of cable tray used to change the direction of the tray assembly a full quarter turn (90). Both vertical and horizontal elbows are common. Used to separate or isolate electrical circuits.

    [PDF Version]
  • Distribution boxes from right to left

    Distribution boxes from right to left

    Excel for Microsoft 365 Word for Microsoft 365 Outlook for Microsoft 365In Office programs, you can quickly align objects (such as pictures, shapes, text boxes, SmartArt graphics, and WordArt.


Optical & Photonic Insights

Need Professional Optical & Photonic Solutions?

Contact us today for product inquiries, custom designs, or technical support